Cooper TS690 Manual de instalación Pagina 54
- Pagina / 60
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Setup New Users
The TS690 and TS690ID allows up to 15 users to
operate the alarm system, each user is assigned a
user type and 4 digit passcode. User 01 is the
master user which has a default setting of 5678.
User Types
The following user types are available:
Master
User 01-15 can be programmed as the type
“Master”. If the installation company has
programmed the master user for full access, they
will have access to all user menus and options. If
the installation company has programmed the
master user for limited access, they will NOT have
access to “User menu 2" options 6 and 8.
Standard
Users 02-15 can be programmed as the type
“Standard”. This user type can set and unset the
alarm system and access ”User menu 1”.
Holiday
Users 02-15 can be programmed as the type
“Holiday”. This user type can set and unset the
alarm system and access “User menu 1”.
However, the passcode is automatically deleted
from the system when a master user passcode is
used to unset the alarm system. Normally the
master user would assign this passcode type a
temporary user whilst they are away on holiday.
Set Only
Users 02-15 can be programmed as “Set Only”.
This user type allows the alarm system to be set
and access to “User menu 1".
Reset Only
Users 02-15 can be programmed as “Reset Only”.
This user type allows 24hr alarms to be reset and
access to “User menu 1" option 1 to 7 and 9.
Duress
Users 02-15 can be programmed as “Duress”.
When this user type is entered a silent “Panic Alarm”
(i.e., Bell and sounders not triggered) is transmitted
to the central station via the telephone line and
remote signalling device (if fitted). The user will still
be able to set and unset the alarm system and
access “User menu 1".
All other user code types will generate a
“Duress” alarm if the passcode is entered
with the first two digits reversed (e.g., for a
standard passcode of 2580 enter 5280 to
generate a “Duress” alarm). If required, this
feature can be disabled by the installation
company or by making the first two digits of
the passcode the same.
PA Code
Users 02-15 can be programmed as “PA Code”.
When this user type is entered a “Panic Alarm”' is
transmitted to the central station via the telephone
line and remote signalling device (if fitted). The
external sounder(s) and strobe light(s) are also
activated.
Shunt
Users 02-15 can be programmed as “Shunt”.
When this user type is entered the circuits assigned
to the shunt group are isolated. When the
passcode is re-entered the circuits assigned to the
shunt group are reinstated.
This user type will be displayed as “Access”
on the TS790 Starburst remote keypad.
54
Appendices TS690 & TS690ID Installation Manual
Setup users
User No. >--
Alter user type
Standard
Change pass code
New code > -----
Change pass code
New code > 2589
Enterusertype:
=Master
= Standard
= Holiday
User Typ
e
4
1
2
3
ENT
Enter user No.
e.g. 04
Enter master user (5678)
=PACode
= Shunt
7
8
ENT
e.g. 1 for Master
Enter New passcode
ENT
e.g. 2589
=SetOnly
4
= Reset Only
5
=Duress
6
User menu 2
Select Option :-
ENTENT
Setup New Users Flowchart
- TS690 & TS690ID 1
- Overview 2
- System Installation 2
- Engineer’s Menu 1 2
- Engineer's Menu 2 3
- Appendices 3
- Number of Zones = 8 to 14 5
- Number of Zones = 2 to 38 5
- Supply: 230V ±10% 50Hz 6
- ID Loop Wiring (TS690ID Only) 8
- Cabling Requirements 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- FUSE 315mA 12
- Installation Procedure 13
- Engineer’s Keypad 14
- TS700 LEC Installation 14
- Wiring Detection Circuits 15
- Double Pole 15
- End Of Line 15
- Wiring ID Biscuits 16
- Biscuit Connections 16
- Wiring A Biscuit to a PIR 16
- External Sounder Connections 17
- Auxiliary Tamper 17
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 18
- DC6 Digi-Modem Installation 18
- Regulatory Requirements 18
- Application 19
- Approval 19
- Connections 19
- Installation 20
- DC54 & DC58M Installation 20
- DATAC or RS232 printer 21
- CPA6 Printer 21
- RS232 Data 21
- Pre Power-Up Checks 22
- Initial Power-Up 23
- Power-Up Checks 23
- NVM Defaults 24
- Panel Outputs [1.1] 26
- Digicom Outputs [1.2] 26
- Digicom Channels [1.3] 26
- Programmable Output Types 26
- No Type/Description 27
- Program Circuits [1.4] 29
- Circuit Types 29
- Circuit Attributes 30
- System Timers [1.5] 31
- Setting Modes [1.6] 33
- Do System Print [1.7] 34
- Remote Reset Algorithm [1.8] 35
- Configuration [1.9] 35
- 34 Entry Keypad Lock 38
- 35 Tamp as Burg 38
- 37 Unconf Usr Rst 38
- 38 Keypad PA On 38
- RESET 1.9V to 2.4V 39
- MID 5.6 to 6.4V 39
- HIGH 9.0 to 10.1V 39
- Relearn Hardware [1.C] 40
- StarburstLCD 42
- Change Passcode [2.4] 43
- Chime Circuits [2.5] 43
- Alter Shunt Group [2.6] 43
- Print System Log [2.7] 43
- Configure Part Sets [2.8] 44
- View System Log [2.9] 44
- Log Event Codes 45
- Reset User Code 1 [2.0] 46
- Start Call Back [2.A] 46
- LCD Only 47
- Modem Password 48
- Modem Site No 48
- Program Digicom 48
- Text Editing Keys 50
- Cursor Types 50
- Common Key Sequences 50
- TS690/TS690ID 53
- Setup New Users Flowchart 54
- Engineers Menu 1 55
- Engineers Menu 2 56
- Output Types 56
- Quick Reference User Menus 57
- User Menu 1 57
- User Menu 2 57
- 496804 Issue 1 60
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper TS690
(432 paginas)
(110 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales