Cooper TS690 Manual de instalación descargar pdf (Pagina 36)

10 Tamp user reset

When programmed as “Yes", tamper alarms

can be reset by the user. When programmed

as ”No", tamper alarms can only be reset by

the engineer or via remote reset. (Default: Yes)

11 Do battery test

When programmed as "Yes" the control panel

battery and any monitored PSU batteries are

tested every hour and when exiting the

engineer's mode. When programmed as "No"

the control panel battery and any monitored

PSU batteries are not tested. (Default: No)

12 F.Exit is NIGHT

When programmed as “Yes" final exit circuits

change to night circuits when the system is part

set. When programmed as ”No" final exit

circuits remain as final exit circuits when the

system is part set. (Default: No)

13 Use code + Enter

When programmed as “Yes", all passcodes

require an additional press of the [ENT] key to

gain access to the system. When

programmed as ”No", access to the system

only requires the entry of the passcode.

(Default: No)

14 Show P.set disp. (LED Keypads)

When programmed as “Yes" the display will

alternate between showing the time and

wards that are set when the system is part set.

When programmed as ”No" the display will

always show the time when the system is part

set. (Default: Yes)

15 Dial Consec.

When programmed as “Yes", the plug-on

digicom attempts calls consecutively. When

programmed as ”No”, the plug-on digicom

attempts calls alternatively. (Default: Yes)

16 SET with AC off

When programmed as “Yes”, the system can

be set without mains power. When

programmed as “No”, the system cannot be

set without mains power. (Default: Yes)

17 Loud Chime tones

When programmed as “Yes” the chime tones

are always at full volume. When programmed

as “No” the chime tones are at the level set by

VR1 on the main PCB. (Default: No)

18 Invert Output 1

When programmed as “Yes” panel output 1 is

normal. When programmed as “No” panel

output 1 is inverted. (Default: No)

19 Invert Digi O/Ps

When programmed as “Yes” the five digicom

outputs on the control panel switch from 0V to

+12V when active (+ve applied). When

programmed as “No” the five digicom outputs

on the control panel switch from +12V to 0V

when active (+ve removed). (Default: No)

20 On-Line keypad

When programmed as “Yes" the Menvier

Lineload On-Line Keypad feature is enabled.

When programmed as “No” the Menvier

Lineload On-Line Keypad feature is disabled.

(Default: Yes)

21 Restore P.I.D

When programmed as "Yes" the Contact ID

restore status is transmitted. When

programmed as "No" Contact ID restore is not

transmitted. (Default: Yes)

22 User Authorised

When programmed as “Yes” the Menvier

Lineload software can only write information to

the control panel after the user has authorised

remote communications. When

programmed as “No” the Menvier Lineload

software can write information to the control

panel without user authorisation. (Default: No)

23 Mimic Alm & Flt.

When programmed as “Yes” any outputs

programmed as the type "Circuit Alarm" will

activate when the relevant circuit is in alarm or

in a fault condition. When programmed as

“No” any outputs programmed as the type

"Circuit Alarm" will activate when the relevant

circuit is in alarm. (Default: No)

24 Monitor off hook

When programmed as “Yes”, the plug-on

digicom will monitor the telephone line for

off-hook conditions (high security line

monitoring). When programmed as “No”, the

plug-on digicom will only monitor the

telephone line for line cut conditions (low

security). (Default: No)

Engineer’s Menu 1 TS690 & TS690ID Installation Manual

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 59 60

Comentarios a estos manuales

Sin comentarios

Cooper TS690 Manual de instalación Pagina 36

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper TS690