Cooper TS690 Manual de instalación descargar pdf (Pagina 31)

System Timers [1.5]

The system timers are as follows:

00 Abort Delay

This timer sets the period in which the alarm

signal may be aborted following an alarm

condition. When an alarm occurs, the “Abort

Output” (043) is only activated if the system is

unset within this period. If the system is unset

after this period the abort output is NOT

activated. The “Alarm” (005) output is also

restored when the abort output is activated.

This timer has a working range of 000-199

seconds. (Default: 180 Secs)

01 No. Re-arms

At the end of the bell duration time the system

re-arms all circuits that are healthy. Circuits that

are still in an alarm condition are isolated until

they change to a healthy condition. This

counter controls the number of times that a

"circuit" will re-arm before it is locked out of the

system. This counter has a working range of

000-199. (Default: 003)

02 Settle Time

When setting the system by “Final Exit” or “Exit

Terminator”, detectors that are on the exit route

sometimes take 3-4 seconds to settle after

activation. The delay programmed in this timer

is used to allow these detectors to settle before

the system or area is set. This timer has a

working range of 000-199 seconds. (Default:

007 Secs)

03 Pset Com. Dly

When the system is part-set the

communication of an alarm signal to the

central station can be delayed by the value

set in this timer. If the timer is set to 199 the

part-set communications are disabled. This

timer has a working range of 000-199 seconds.

If you set this timer to 199 then the control

panel overrides keypad lockout during

part-set.

Cooper Security also recommends that

you change the digicom output type

(see Eng 1.2 or 1.3) from 008 to 047. This

will stop the control panel transmitting a

close signal when the users part set the

system.

(Default: 000 Secs)

04 Exit Time

This timer sets the delay between the user

initiating the exit procedure and the system (or

area) actually setting. If during the exit time an

“Exit Terminator” circuit is activated the exit time

is cancelled and the system sets immediately.

This timer has a working range of 000-199

seconds. (Default: 030 Secs)

05 Entry Time

When the system is set or part-set, and the entry

procedure is initiated, the entry timer starts to

count down. If a valid user passcode has not

been entered when the timer reaches zero,

the internal sounders are activated and the

“2nd Entry” timer is started. This timer has a

working range of 000-199 seconds. (Default:

015 Secs)

TS690 & TS690ID Installation Manual Engineer’s Menu 1

Program circuits

Enter CCT No.>--

CCT 04 NIGHT

CCT 04 F.EXIT

>********

CCT 04 F.EXIT

>*******C

Enter circuit type:

= Not Used

=Night

= 24hr

= PA Silent

Circuit No.

Attributes

Circuit Type

ENT

Enter circuit No.

e.g. 04

=Fire

= Auxiliary

= Final Exit

ENT

e.g. 7 for Final Exit

Select attributes:

= ccessA

= KnockD

=estT

=esetR

=onitoredM

=ntryE

ENT

e.g. 8 for chime

= PA Audible

=mitO4 =himeC8

Engineers menu 1

Select Options :-

StarburstLCD

LED

E1 -

ENGR 1 -

CT.--

CCT NO.--

NITE

NIGHT

F.EXIT

CHI

F.EXIT

CHIME

= Exit Terminator

=KeyPoint

Program Circuits Flowchart

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 59 60

Comentarios a estos manuales

Sin comentarios

Cooper TS690 Manual de instalación Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper TS690