Cooper TS690 Manual de instalación descargar pdf (Pagina 29)

and the circuit remains active until the end of

the confirmation time then the control panel

omits the active zone and triggers the Active

Omit output. The control panel deactivates

the output when a user disarms the system.

Use existing output type 036 = System Open to

indicate Unset Complete.

100 - 137 Circuit Mimic

Will mimic (active when circuit is active) circuits

01 to 38 respectively.

200 - 237 Circuit Alarms

Active when a circuit causes an alarm, or is

activated during a walk test, for circuits 01 to

38 respectively.

Following a wallk test, the operator can

confirm the operation of all the appropriate

circuits at a mimic panel. The control unit

clears these indications when the operator

enters a valid passcode.

Program Circuits [1.4]

The TS690 can monitor up to 14 detection circuits,

whereas the TS690ID can monitor up to 38

detection circuits. Each circuit must be

programmed in order for the system to respond

correctly.

Circuit Types

The circuit type defines how the circuit will respond

when it is triggered. The following circuit types are

available:

0 Not Used

A circuit that will never generate any alarm.

1 Night

A circuit that will generate a full alarm when the

system is set.

2 24hr

A circuit which is monitored at all times. When

triggered in the unset condition a local alarm is

generated and when triggered in the set

condition a full alarm is generated.

3 PA Silent

A circuit which is monitored at all times. When

triggered it will activate any outputs that are

programmed as P.A.

4 PA Audible

A circuit which is monitored at all times. When

triggered it will activate any outputs that are

programmed as P.A. and generate a full

alarm condition.

5 Fire

A circuit that is normally connected to a smoke

detector. When triggered it will generate a fire

tone on the internal sounders, the external

sounders are pulsed for the bell duration and

any outputs programmed as fire will be

activated.

6 Auxiliary

A circuit which is monitored at all times. When

triggered it will activate any outputs

programmed as Auxiliary.

7 Final Exit

This must be the first detector or door contact

that is triggered when entering the protected

area. When the setting mode for the system is

programmed for Final Exit setting, opening

and closing of this circuit during the exit

procedure will cause the system to set. Once

set, activation of this circuit will start the entry

timer.

8 Exit Terminator

A circuit that is normally connected to a push

button outside the protected premises, which

can be used to finally set the system or area.

9 Keyswitch

(Also includes Lockset.) A circuit that may be

connected to a keyswitch to allow setting

and/or part-setting of the system.

The Keyswitch circuit has two groups of

attributes. The first group of attributes control

the wards that are set/unset when the circuit is

switched between “Healthy” and “Active”. The

second group of attributes selects the type of

Keyswitch (Momentary or Latched) or selects

the Lockswitch zone type.

When programming the Keyswitch circuit the

eight standard attributes are not available,

instead the attributes are used to select the

Keyswitch operation as follows:

[1] Full Set Group - “Healthy” to “Active”.

[2] Code Set Group A - “Healthy” to “Active”.

[3] Code Set Group B - “Healthy” to “Active”.

[4] Code Set Group C - “Healthy” to “Active”.

[5] Lockset - See Lockset Exit Mode.

[6] Momentary - Use for Momentary type

keyswitches. De-select for Latched

keyswitches.

TS690 & TS690ID Installation Manual Engineer’s Menu 1

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 59 60

Comentarios a estos manuales

Sin comentarios

Cooper TS690 Manual de instalación Pagina 29

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper TS690