Cooper TS690 Manual de instalación Pagina 20
- Pagina / 60
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation
For your safety, installation of the DC6
MUST be carried out in the sequence
shown below:
1. Ensure that all power is removed from the
system i.e. mains supply and standby battery.
2. Remove the DC6 from its packaging and fit
the plastic mounting pillars into the 4 holes
provided.
3. Align the DC6 with the connector JP4 on the
main PCB and push firmly into place.
4. Connections to the telephone network must
be made via a NET master socket (Line Box).
5. Using the cable type 1/0.5mm CW1308, strip
back 5mm of the required cores and feed into
the control panel though the appropriate
cable entry. Keep all telephone cables at least
5mm away from other alarm cables.
6. Connect the two telephone cables to the
terminal blocks A and B, see figure 22.
7. Remove the two screws from the BT master
jack socket and remove the bottom section
from the master jack.
8. Connect the cable from A and B terminals on
the DC6 to the BT master jack terminals, see
figure 22.
9. A special insertion tool will be required to
connect the cable to the master jack, this is
available from RS Components (Part No.
470-487).
10.Replace the bottom section of the master jack
socket and replace the two screws.
11.Re-apply power to the control panel.
12.The DC6 must now be programmed, refer to
"Modem Options” on page 47.
13.Each channel can be tested using the
Digicom Test routine, see page 49.
14.Finally replace and secure the cover on the
control panel.
DC54 & DC58M Installation
A plug-on digital communicator DC54, DC58 or
DC58M may be fitted inside the control panel to
allow alarm status information to be transferred to
a dedicated central station. The unit should be
fitted in accordance with the installation
instructions supplied with it and connected to the
control panel plug DIGI-MODEM (JP3) using the
lead provided with the unit. The NVM within the will
need to be programmed using an engineer’s
keypad or PP5.
The control panel can only support one
plug-on Digi-Modem either the DC6 or
DC54/58M. Do not connect both types to
same control panel.
20
System Installation TS690 & TS690ID Installation Manual
Connect to JP3
DIGI-MODEM
Plug-on digicom / digi-modem
A
B
BC
B.T. master jack ( Type NTE5
user accessible connections )
A(5) = White / Blue ring
BC(3) = Orange / White ring
B(2) = Blue / White ring
Telephone cable
(Type 1/0.5mm CW1308)
6
5
4
3
2
1
Figure 23. DC54/DC58 Connections
- TS690 & TS690ID 1
- Overview 2
- System Installation 2
- Engineer’s Menu 1 2
- Engineer's Menu 2 3
- Appendices 3
- Number of Zones = 8 to 14 5
- Number of Zones = 2 to 38 5
- Supply: 230V ±10% 50Hz 6
- ID Loop Wiring (TS690ID Only) 8
- Cabling Requirements 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- FUSE 315mA 12
- Installation Procedure 13
- Engineer’s Keypad 14
- TS700 LEC Installation 14
- Wiring Detection Circuits 15
- Double Pole 15
- End Of Line 15
- Wiring ID Biscuits 16
- Biscuit Connections 16
- Wiring A Biscuit to a PIR 16
- External Sounder Connections 17
- Auxiliary Tamper 17
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 18
- DC6 Digi-Modem Installation 18
- Regulatory Requirements 18
- Application 19
- Approval 19
- Connections 19
- Installation 20
- DC54 & DC58M Installation 20
- DATAC or RS232 printer 21
- CPA6 Printer 21
- RS232 Data 21
- Pre Power-Up Checks 22
- Initial Power-Up 23
- Power-Up Checks 23
- NVM Defaults 24
- Panel Outputs [1.1] 26
- Digicom Outputs [1.2] 26
- Digicom Channels [1.3] 26
- Programmable Output Types 26
- No Type/Description 27
- Program Circuits [1.4] 29
- Circuit Types 29
- Circuit Attributes 30
- System Timers [1.5] 31
- Setting Modes [1.6] 33
- Do System Print [1.7] 34
- Remote Reset Algorithm [1.8] 35
- Configuration [1.9] 35
- 34 Entry Keypad Lock 38
- 35 Tamp as Burg 38
- 37 Unconf Usr Rst 38
- 38 Keypad PA On 38
- RESET 1.9V to 2.4V 39
- MID 5.6 to 6.4V 39
- HIGH 9.0 to 10.1V 39
- Relearn Hardware [1.C] 40
- StarburstLCD 42
- Change Passcode [2.4] 43
- Chime Circuits [2.5] 43
- Alter Shunt Group [2.6] 43
- Print System Log [2.7] 43
- Configure Part Sets [2.8] 44
- View System Log [2.9] 44
- Log Event Codes 45
- Reset User Code 1 [2.0] 46
- Start Call Back [2.A] 46
- LCD Only 47
- Modem Password 48
- Modem Site No 48
- Program Digicom 48
- Text Editing Keys 50
- Cursor Types 50
- Common Key Sequences 50
- TS690/TS690ID 53
- Setup New Users Flowchart 54
- Engineers Menu 1 55
- Engineers Menu 2 56
- Output Types 56
- Quick Reference User Menus 57
- User Menu 1 57
- User Menu 2 57
- 496804 Issue 1 60
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper TS690
(432 paginas)
(110 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales