Cooper TS690 Manual de instalación descargar pdf (Pagina 37)

25 Answer Phone Def

When programmed as “Yes”, the plug-on

digi-modem will only answer incoming calls

after a second attempt. When programmed

as “No”, the plug-on digi-modem will answer

incoming calls after the modem ring counter

has expired. (Default: No)

26 Send Open/Close

This configuration option will only effect

Extended format signalling, see configuration

option 08. When programmed as “Yes”, the

plug-on digi-modem will send Open and

Close signals (codes 401 & 409) to the central

station. When programmed as “No”, the

plug-on digi-modem will not send Open and

Close signals (codes 401 & 409) to the central

station. (Default: Yes)

27 Tamper always

This configuration option will only effect

Extended format signalling, see configuration

option 08. When programmed as “Yes”, the

plug-on digi-modem will send tamper alarm

signals (codes 137 & 383) to the central station

at all times. When programmed as “No”, the

plug-on digi-modem will only send tamper

alarm signals to the central station when the

system is set or part set. (Default: No)

28 24Hr Ccts always

This configuration option will only effect

Extended format signalling, see configuration

option 08. When programmed as “Yes”, the

plug-on digi-modem will send 24hr/Auxilliary

alarm signals (codes 135 & 150) to the central

station at all times. When programmed as

“No”, the plug-on digi-modem will only send

24hr/Auxilliary alarm signals to the central

station when the system is set or part set.

(Default: No)

29 Keypad PA Silent

When programmed as “Yes”, pressing 1&3on

the remote keypad will generate a silent PA

alarm. When programmed as “No”, pressing 1

& 3 on the remote keypad will generate an

audible PA alarm. (Default: No)

The Keypad PA feature is only available

on remote keypads fitted with version 4.0

software or above.

30 Sounder on Confirm

When programmed as “Yes” the control unit

activates the internal sounders after a

confirmed alarm and any programmed bell

delay. When programmed as “No” the control

unit starts the internal sounders immediately

after an unconfirmed alarm. (Default = No)

31 Bells on Confirm

When programmed as “Yes” the control unit

activates the external sounders after a

confirmed alarm and any programmed bell

delay. When programmed as “No” the control

unit activates the external bell immediately

after an unconfirmed alarm. (Default = No)

32 Confirmation After Entry

When programmed as “Yes” the control unit

sends a confirmed alarm if the intruder

activates one or two separate zones after the

entry timer expires. To select between one or

two zones use “36 Entry conf 2 cct” When

programmed as “No” the control unit disables

alarm confirmation when a user starts the entry

timer. Use the “No” option to comply with

DD243:2002 paras 6.4.2, 6.4.3, 6.4.4 and

6.4.6.

(Default = No)

33 Confirmation On

When programmed as “Yes” then the Digicom

reports a Channel 3 (005 Intruder) for an

intruder alarm as normal. If a subsequent zone

is triggered within the same set period then the

Digicom reports Channel 7 (011 Confirmed

Alarm). The ARC operator can now inform the

appropriate police authority that the alarm is

confirmed and that this is likely to be a real

break in and not a false alarm.

When programmed as “No” then the control

panel disables Alarm Confirmation and any

Alarm Confirm outputs.

(Default = Yes)

TS690 & TS690ID Installation Manual Engineer’s Menu 1

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 59 60

Comentarios a estos manuales

Sin comentarios

Cooper TS690 Manual de instalación Pagina 37

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper TS690