Cooper 9940 Guía de usuario

USER GUIDE HARDWIRED CONTROL UNIT

2. Everyday Operation Page 10 497282 General Procedure To set the system: 1. Secure all doors and windows. 2. At the keypad, key in an access cod

2. Everyday Operation 497282 Page 11 Timed Set With Timed Set, the system sets after a programmed exit time has expired. The time starts when you p

2. Everyday Operation Page 12 497282 waiting for an exit time. The system gives a double "beep" to show that it is set. Note: Instant Set i

2. Everyday Operation 497282 Page 13 Investigating Setting Problems This section offers general guidance. If you need assistance to resolve a probl

2. Everyday Operation Page 14 497282 Other Problems The system informs you of problems through alerts. These are warnings communicated through the ke

2. Everyday Operation 497282 Page 15 Unsetting the System WARNING: If you enter your premises and an internal alarm starts, there may be an intrud

2. Everyday Operation Page 16 497282 Aborting False Alarms If your system is connected to an ARC and you accidentally cause an alarm, you normally ha

497282 Page 17 3. After an Alarm Responding to a Fire Alarm IMPORTANT: The system gives a fire alarm by sounding a two-tone warning from the keypads

Page 18 497282 4. Special Functions Introduction As well as setting and unsetting the system, you can perform a number of other functions from the

Appendix 497282 Page 19 Viewing Alerts The system records alarms, faults and tampers as alerts. It usually displays the first alert automatically w

Page 2 497282 Contents 1. Introduction ...3 Alarm System...3 Keypad...

Appendix Page 20 497282 Omitting Zones Your system may be programmed so that you can omit individual detectors. This enables you to ignore alarms com

Appendix 497282 Page 21 Requiring User Code before Installer Code You can specify that a user code must be entered before the installer code to acc

Appendix Page 22 497282 Turning the Chime On and Off Your system may be programmed so that a chime tone sounds when certain doors are opened while th

Appendix 497282 Page 23 Testing Zones You can set the system so that it will allow you to walk around and test each of the detectors (a walk test).

Appendix Page 24 497282 When the system is delivered from the factory, all access codes are set to default values. Depending how your installer has s

Appendix 497282 Page 25 To delete an access code: 1. Follow the procedure for setting an access code. 2. In step 5, key in "0000". Ch

Appendix Page 26 497282 Proximity Tags Each normal user (Users 2 to 50) can have a tag, an access code or both. You cannot assign a tag to the master

Appendix 497282 Page 27 Appendix. Log Messages Message Meaning AC Fail Mains power supply failed AC Restore Mains power supply restored Al Conf D

Appendix Page 28 497282 Message Meaning System Tamp Rst System tamper reset System Tamper System tamper Tamper F== Rstr Forbikobler keypad == tamper

Page 29 497282 NOTES

497282 Page 3 1. Introduction Alarm System The alarm system described in this book comprises a control unit (model 9651), one or more keypads, and v

Appendix Page 30 497282 NOTES

Log Messages 497282 Page 31 NOTES

Page 32 497282 Issue 1 Your Installation Zone Description A B C DOmit AllowChimeEntry Time 1 2 3 4 5

1. Introduction Page 4 497282 Keypad Your alarm system is fitted with a 9930 or 9940 keypad, from which you can set and unset the system. Figures 1 a

1. Introduction 497282 Page 5 Figure 1. 9930 LCD Remote Keypad Alert lamp (see page 20)Flashes to highlight unacknowledged alarm, fault or tamper

1. Introduction Page 6 497282 Figure 2. 9940 LCD Remote Keypad AB CD1234567890Alert lamp (see page 20)Flashes to highlight unacknowledged alarm, fau

1. Introduction 497282 Page 7 Mains Power Failures The control unit indicates mains power failures using alerts. If the supply has since been resto

1. Introduction Page 8 497282 About this Guide The rest of this guide tells you how to use the system: 2. Everyday Operation Tells you how to set an

497282 Page 9 2. Everyday Operation During installation, your installer programs the system to create an exit route and entry route for your premise